Darthpedge
Registered user
Registered: 02-2012
Location: UK
Posts: 323
Karma: 10 (+13/-3)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Yes bud I was going to but the ones with the mounting blocks 
|
|
6/12/2012, 1:14 pm
|
Link to this post
Send Email to Darthpedge
Send PM to Darthpedge
Blog
|
GordonTarpley
Registered user
Registered: 06-2011
Location: Tampa, FL
Posts: 303
Karma: 4 (+4/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Ok, I'll check them shortly and add a post when they've been re-uploaded. 
|
|
6/12/2012, 1:15 pm
|
Link to this post
Send Email to GordonTarpley
Send PM to GordonTarpley
Blog
|
GordonTarpley
Registered user
Registered: 06-2011
Location: Tampa, FL
Posts: 303
Karma: 4 (+4/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
I'm RECHECKING some parts...
a few that didn't get flagged printed incorrectly. I got some new software that will help me do some final checks on the models before they get uploaded.
I did some screen shots to show the insides of a few of the Hollow and Semi Solid models....
This part, hollow forearm large greelbie, printed in two pieces because of flipped faces on one half (marked in red)
Solid models should still be good. double checking all the hollow and simi solid models over the next few days....
|
|
6/13/2012, 4:58 am
|
Link to this post
Send Email to GordonTarpley
Send PM to GordonTarpley
Blog
|
GordonTarpley
Registered user
Registered: 06-2011
Location: Tampa, FL
Posts: 303
Karma: 4 (+4/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
A fellow builder purchased some parts and the Hollow forearm greelbie showed up in two pieces. BUT not where I expected based on the new software I'm using to check the files.
The issue was something the auto-check wouldn't find to be a problem. I would have no idea about if it weren't for builder feedback so if you have any comments on parts, good or bad always let me know so I can make improvements.
a new versions of the parts should be uploaded today.
Last edited by GordonTarpley, 6/13/2012, 12:47 pm
|
|
6/13/2012, 10:24 am
|
Link to this post
Send Email to GordonTarpley
Send PM to GordonTarpley
Blog
|
Darthpedge
Registered user
Registered: 02-2012
Location: UK
Posts: 323
Karma: 10 (+13/-3)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Dude Rome wasn't built in a day keep up the good work come to think about nor will my c3po as waiting for my armour lol
|
|
6/13/2012, 11:49 am
|
Link to this post
Send Email to Darthpedge
Send PM to Darthpedge
Blog
|
matthew007
Registered user
Registered: 01-2010
Posts: 521
Karma: 5 (+5/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
How much are all these parts
|
|
6/13/2012, 12:55 pm
|
Link to this post
Send Email to matthew007
Send PM to matthew007
|
GordonTarpley
Registered user
Registered: 06-2011
Location: Tampa, FL
Posts: 303
Karma: 4 (+4/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
They vary depending on the build. I'm trying to do a Solid, Semi Solid, and Hollow version of each part. They'll all look the same on the outside but have different amounts of material on the inside to help control cost.
The hollow parts are cheapest but they'll need some reinforcing to keep them from being too flimsy.
There should be a link to the Shapeways store on in the first post. I've disabled a few versions of parts while i do some adjustments to the geometry but they'll be back up there soon.
|
|
6/13/2012, 1:25 pm
|
Link to this post
Send Email to GordonTarpley
Send PM to GordonTarpley
Blog
|
Darthpedge
Registered user
Registered: 02-2012
Location: UK
Posts: 323
Karma: 10 (+13/-3)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Gordon my parts have arrived and not only did they arrive super quick they look the nuts buddy top work fella I will order other bits when you sorted out minor glitchs again nice one bud now time to fill in my lid to fit smaller eyes aaaaaaaaaaaaaaaarr r hhhhh
|
|
6/14/2012, 1:23 pm
|
Link to this post
Send Email to Darthpedge
Send PM to Darthpedge
Blog
|
GordonTarpley
Registered user
Registered: 06-2011
Location: Tampa, FL
Posts: 303
Karma: 4 (+4/-0)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Great to hear! If you get a chance to snap some photos I'd love to see how they look.
Thanks!!!
|
|
6/14/2012, 4:45 pm
|
Link to this post
Send Email to GordonTarpley
Send PM to GordonTarpley
Blog
|
Darthpedge
Registered user
Registered: 02-2012
Location: UK
Posts: 323
Karma: 10 (+13/-3)
|
|
Reply | Quote
|
|
Re: 3d Printed Parts
Ok buddy just need to figure out how to do that lol
|
|
6/15/2012, 1:14 am
|
Link to this post
Send Email to Darthpedge
Send PM to Darthpedge
Blog
|
